Acoustic leak detection
We pressurize the system and use listening discs and a pipe inspection camera to mark the leak within 6 to 12 inches. You see the spot before we cut. This step is included when you approve the repair.
Acoustic detection, precise tunneling, and code-correct copper or PEX repairs
Slab leak repair brea CA that stops hidden water loss
When you need slab leak repair brea CA homeowners trust, our team pinpoints the break before we break concrete. We handle under-slab copper and PEX failures across Orange County, from Downtown Brea bungalows to 1970s tracts near Olinda. If your water bill jumped and the floor feels warm, call 714 880 7135 for same-day slab leak detection brea service.
Careful work. Honest options.
About this service
What slab leak repair brea CA actually involves
Slab leak repair brea CA is the process of locating and fixing a pressurized water line failure beneath a concrete foundation without tearing up the whole floor. We start with acoustic listening discs and a pipe inspection camera, isolate the hot or cold line, then open a small access point. Most repairs use copper pipe or PEX tubing with SharkBite or Uponor fittings, and we pressure-test to 80 psi before closing the slab. A typical job runs four to eight hours from detection to backfill.
Homes in Brea built between the 1950s and 1980s often sit on copper supply lines that have finally given out. Hard water from the local aquifer accelerates pitting, and a pinhole can dump hundreds of gallons under your foundation before you see a wet spot. That is why brea slab leak repair services start with detection, not demolition. If you are searching for how to find a slab leak brea CA, the answer is a trained ear and the right leak detection equipment, not a sledgehammer.
- ✓ Stop foundation damage
- ✓ Cut water waste fast
- ✓ Protect flooring and finishes
- ✓ Restore hot water pressure
What's included
What our slab leak repair includes
Every slab leak repair brea CA job includes detection, access, repair, pressure testing, and cleanup. We do not charge extra for the detection if you approve the repair. Add-ons like whole-home repiping or water softener installation are quoted separately.
Small access point
We cut a 12 by 12 inch access point in the slab, not a trench. That preserves your flooring and keeps restoration costs down. We match the concrete patch to your existing slab when we close it.
Copper or PEX repair
We repair copper with a soldering torch and couplings, or join PEX with a pex crimping tool and SharkBite or Uponor fittings. All materials meet Uniform Plumbing Code and California Plumbing Code requirements.
80 psi pressure test
Before backfill, we hold the repaired line at 80 psi for 30 minutes. You get a written pass result and photos. If pressure drops, we find the second leak now, not after the concrete is back.
Cleanup and patch
We backfill with sand, pour a concrete patch, and clean the work area. You can walk on the patch in 24 hours. We haul away all debris and leave the room ready for normal use.
How it works
How our slab leak repair process works
Call 714 880 7135 and describe what you see: warm floor, spinning meter, or a water bill jump. We ask three questions to narrow the likely line and schedule a same-day or next-morning window. You get a text when the technician is 30 minutes out.
On site, we pressurize the system and use acoustic listening equipment and a pipe inspection camera to isolate the break within 6 to 12 inches. This step takes 45 to 90 minutes. You watch the readings and see the exact spot marked on the floor.
We cut a small access point, usually 12 by 12 inches, and expose the failed section. Copper is repaired with a soldering torch and couplings; PEX is joined with a pex crimping tool. Most repairs take two to four hours once the line is exposed.
Before anything is closed, we pressure-test the repaired line to 80 psi and hold it for 30 minutes. If it drops, we find the second leak now, not after the concrete is back. You get a written pass result and photos of the repair.
We backfill with sand and a concrete patch that matches your slab, then clean the work area. Total time on site is usually four to eight hours. You can walk on the patch in 24 hours and return to normal use immediately.
STEP 01Phone triage
Call 714 880 7135 and describe what you see: warm floor, spinning meter, or a water bill jump. We ask three questions to narrow the likely line and schedule a same-day or next-morning window. You get a text when the technician is 30 minutes out.
Tools & methods
Tools and methods we use
Acoustic listening discs
We place these on the floor to hear the sound of pressurized water escaping a pipe. They pinpoint the leak within 6 to 12 inches before we cut.
Pipe inspection camera
A flexible camera goes into the line to confirm the leak location and check for corrosion or root intrusion nearby. It shows us the pipe material and condition.
Soldering torch
Used to sweat copper couplings and repair copper supply lines. We keep the flame controlled and shield nearby materials to protect your home.
PEX crimping tool
Joins PEX tubing with crimp rings and fittings from SharkBite or Uponor. PEX repairs are fast, flexible, and resistant to the hard water in Brea.
Pressure test gauge
We pressurize the repaired line to 80 psi and hold it for 30 minutes. The gauge confirms the repair before we close the slab.
Hydro jetting machine
If the drain line is clogged while we are on site, we jet it at 4,000 psi to clear grease and scale. One visit handles both problems.
Real results
Before and after.
Slab Leak Repair
Downtown Brea copper pinhole repair
A homeowner in Downtown Brea noticed a $290 water bill and a warm spot near the hallway. The meter spun with all fixtures off. We detected a pinhole in the hot copper line 4 feet from the water heater.
After: We opened a 12-inch access point, replaced 18 inches of copper with two couplings, and pressure-tested to 80 psi. The bill dropped back to $85 the next month, and the floor cooled within hours.
Book this service →
Slab Leak Repair
Olinda PEX crimp failure
A 1990s home in Olinda had water seeping through the grout in the guest bathroom. The PEX line under the slab had a failed crimp ring. The homeowner had already replaced the flooring once.
After: We located the failed ring with a camera, cut a small access point, and replaced the fitting with a new Uponor connection. Pressure held at 80 psi for 30 minutes. The repair cost $1,150 and saved the new flooring.
Book this service →
Slab Leak Repair
Carbon Canyon hot line reroute
A Carbon Canyon home had two slab leaks in three years, both on the hot line. The homeowner was tired of cutting concrete and wanted a permanent fix. The copper line was corroded along its length.
After: We rerouted the hot line overhead through the attic using PEX tubing, abandoning the under-slab pipe. The job took two days and cost $3,800. No more slab leaks, and the water pressure improved to 65 psi at the kitchen tap.
Book this service → Problems we solve
Slab leak problems we solve in Brea
A slab leak is rarely just a wet floor. It drives up your water bill, cracks your foundation, and can force you out of a bathroom for weeks. Here are the problems we fix most often in Brea.
Ask a pro →Water bill jumped 30% with no change in use
We isolate the hot and cold lines, use acoustic detection to find the break, and repair the section. Most customers see their bill return to normal the next billing cycle.
Warm spot on the floor near the bathroom
We shut down the hot line, detect the exact break, and repair it with copper or PEX. The warm spot disappears as soon as the line is fixed and pressure-tested.
Sound of running water when everything is off
We trace the sound with listening equipment, open a small access point, and fix the line. We also check for a second leak before closing the slab.
Cracks in drywall or sticking doors
We repair the leak, pressure-test the line, and recommend a foundation inspection if movement is visible. Fixing the water source stops the damage from getting worse.
Proof you can check
Licensed, certified, and reviewed
- California C-36 Plumbing License · California Contractors State License Board (CSLB)
- IAPMO Certification · International Association of Plumbing and Mechanical Officials
- Backflow Prevention Certification · California Department of Public Health approved program
- EPA WaterSense Partner · U.S. Environmental Protection Agency
- OSHA Safety Certification · Occupational Safety and Health Administration
Customer reviews
What Brea homeowners say
★★★★★
“Our water bill doubled and the kitchen floor was warm. Ace found the leak under the slab in under an hour with their listening equipment. They cut one small square, replaced a copper section, and pressure-tested it. Total was $1,850 and we kept our tile. No other company even offered to test before cutting.”
MG
Maria G.Homeowner, Downtown Brea
✓ Verified“
★★★★★
“A pinhole leak in the hot line had been soaking our foundation for months. The crew showed up at 7 a.m., located it with a camera, and had it repaired by 2 p.m. They showed me the pressure test at 80 psi and cleaned up better than they found it. Fair price, no upsell.”
DR
Dan R.Homeowner, Olinda
✓ Verified★★★★★
“We called at 11 p.m. with water coming up through the grout. They walked us through shutting off the main and had a tech out by 6 a.m. The leak was in a PEX line, and they fixed it the same morning. I appreciated the straight answers and the written price before they started.”
PS
Priya S.Homeowner, Carbon Canyon
✓ VerifiedMost slab leak repairs in Brea run $950 to $4,500, with the average around $2,200. Cost depends on whether the leak is under tile or carpet, how deep the line sits, and whether we repair a section or reroute the whole line. Detection alone is $250 to $450. You get a written price before we cut.
Four signs point to a slab leak: a water bill that jumps 20% or more with no change in use, a warm spot on the floor, the sound of running water when everything is off, and cracks in tile or drywall. Check your meter, write down the reading, wait two hours with no water use, and read it again. Any movement means a leak.
The best company is the one that detects before it demolishes. Look for a California C-36 Plumbing License, acoustic detection equipment, and a written pressure-test result. We have been fixing Brea slab leaks since 2017, carry IAPMO Certification, and pressure-test every repair to 80 psi before we close the slab.
Most repairs take four to eight hours from detection to backfill. Detection runs 45 to 90 minutes, the repair itself takes two to four hours, and pressure testing adds 30 minutes. If the leak is under tile, add an hour for careful cutting. You can walk on the patch in 24 hours.
Ready when you are
Get slab leak repair brea CA before the floor cracks
Every day you wait, water erodes more soil under your foundation. Call 714 880 7135 now and we will pinpoint the leak, give you a written price, and fix it with a licensed technician. Same-day detection available.
Call Now 714 880 7135 →
Request an appointment
Call Ace Plumbing Brea CA
Reach us at 714 880 7135 for same-day service or 24/7 emergency dispatch. We answer the phone, ask what's going on, and give you a realistic arrival window. Most calls placed before noon get a plumber the same day. You can also email info@aceplumbingbreaca.com for non-urgent quotes and scheduling.
Call anytime714 880 7135Email the officeinfo@plumbingbreaca.com
Office hoursOpen 24 hours · 7 days a week