Camera inspection
We record the full line from the house to the city connection using a RIDGID pipe inspection camera. You see the footage in real time. This step identifies pipe material, clog type, and any existing damage before we jet.
High pressure drain cleaning brea done right the first time
Hydro jetting brea CA clears your worst drain fast
When a drain backs up, hydro jetting brea CA is the fastest way to clear grease, roots, and scale without harsh chemicals. We serve homeowners and businesses across brea, California with same-day high pressure drain cleaning brea that restores full flow and keeps it that way. One call, one visit, and your line runs like new.
Careful work. Honest options.
About this service
What hydro jetting brea CA actually does
Hydro jetting brea CA is a drain and sewer cleaning method that uses pressurized water, typically 3,000 to 4,000 PSI, to scour the inside of pipes back to bare wall. A flexible hose with a specialized nozzle enters through a cleanout or access point and blasts water backward, pushing debris toward the sewer main. Unlike a drain snake that only pokes a hole through a clog, this process removes the buildup entirely, including grease, soap scum, scale, and root mass.
Brea homes built before the 1990s often have cast iron or Orangeburg sewer laterals that collect scale and root intrusion over time. If you are searching for hydro jetting near me brea, the problem is usually recurring backups, slow drains, or gurgling fixtures. We run a pipe inspection camera first to confirm pipe material and condition, then match water pressure to what your line can safely handle. That step prevents damage and gives you a clear picture of what is happening underground.
- ✓ Removes roots at the source
- ✓ Safe for older pipes when sized right
- ✓ No harsh chemicals
- ✓ Longer-lasting results
What's included
What our hydro jetting service includes
Every hydro jetting visit includes a camera inspection, the jetting itself, flow testing, and cleanup. We do not charge extra for standard access through an existing cleanout. If your line needs a new cleanout or the clog is in a city main, we will explain the difference before any work begins.
Hydro jetting
We use a truck-mounted or portable hydro jetting machine with a rotating nozzle to scour the pipe wall. Pressure is matched to your pipe material, from 1,500 PSI for old cast iron up to 4,000 PSI for PVC and ABS.
Flow testing
After jetting, we fill and drain every fixture on the line, including toilets, tubs, and sinks. If any fixture still drains slowly, we jet that section again. We do not leave until the line flows freely.
Cleanout cap replacement
We replace the cleanout cap with a new one if the old cap is cracked or missing. A proper cap keeps sewer gas out of your yard and prevents debris from entering the line between cleanings.
Written summary
You get a written note of what we found, what we cleared, and any sections that need future attention. If we saw roots or scale returning, we will suggest a maintenance interval based on your line condition.
How it works
Our hydro jetting process step by step
We insert a RIDGID pipe inspection camera through the cleanout and record the line from the house to the city main. You see the footage on screen. This step identifies root intrusion, bellies, cracks, and pipe material so we choose the right pressure and nozzle. Takes 20 to 30 minutes.
We locate the cleanout, remove the cap, and protect the surrounding floor or yard with drop cloths. If the cleanout is missing or buried, we can jet through a toilet pull or roof vent. We confirm water supply and set up the hydro jetting machine within 10 feet of the access point.
The hose feeds into the line while the nozzle blasts water backward, scouring the pipe wall and pushing debris toward the main. We work in passes, starting at the clog and moving toward the street. Grease and scale come out first; roots take longer. Expect 45 to 90 minutes of active jetting.
We run the camera again to confirm the pipe is clean and check for any damage the jetting may have revealed. Then we fill and drain multiple fixtures, including the toilet, tub, and kitchen sink, to confirm full flow. If anything is still slow, we jet that section again at no extra charge.
We replace the cleanout cap, wipe down surfaces, and haul away debris. Before we leave, we show you the before-and-after camera footage and note any pipe sections that may need future repair. You get a written summary of what we found and what we did.
STEP 01Camera inspection
We insert a RIDGID pipe inspection camera through the cleanout and record the line from the house to the city main. You see the footage on screen. This step identifies root intrusion, bellies, cracks, and pipe material so we choose the right pressure and nozzle. Takes 20 to 30 minutes.
Tools & methods
Tools and methods we use
RIDGID pipe inspection camera
Records the inside of the pipe so we can see clogs, roots, cracks, and pipe material before and after jetting. The footage is saved and shown to you on site.
Hydro jetting machine
Truck-mounted or portable unit that delivers 1,500 to 4,000 PSI of water through a flexible hose. Pressure is adjusted based on pipe material and condition.
Root-cutting nozzle
A rotating nozzle with hardened blades that slices tree roots into small pieces and flushes them out of the line. Used for root intrusion in sewer laterals.
Penetrating nozzle
A pointed nozzle that blasts through soft clogs like grease and soap scum. It opens a path first, then we switch to a wider nozzle to clean the pipe wall.
Drain snake and sewer auger
Used for light clogs or to retrieve foreign objects before jetting. Sometimes a snake is all a branch line needs, and we will tell you that instead of upselling jetting.
Leak detection equipment
Acoustic listening devices and thermal imaging cameras that help us find hidden leaks in supply or drain lines when symptoms point to a break rather than a clog.
Real results
Before and after.
Hydro Jetting
Kitchen line cleared of grease
A Downtown Brea homeowner dealt with a slow kitchen sink for months. Store-bought cleaners helped for a week, then the backup returned. The pipe was coated with a half-inch of grease and food particles from years of cooking.
After: We jetted the branch and main line at 3,000 PSI with hot water. The camera showed bare pipe wall from the trap to the city main. Flow test on the sink and dishwasher ran full speed. The job took 75 minutes.
Book this service →
Hydro Jetting
Root mass removed from sewer lateral
A Carbon Canyon home backed up into the yard during a rainstorm. The camera showed a root ball blocking 80 percent of the four-inch lateral about 30 feet from the cleanout. The pipe had a hairline crack at a joint.
After: We used a root-cutting nozzle at 2,500 PSI to slice and flush the roots. The camera confirmed full flow and clean pipe walls. The crack was small enough to monitor rather than repair immediately. Job time was two hours.
Book this service →
Hydro Jetting
Scale removed from old cast iron
An Olinda fourplex had recurring slow drains in two units. The 1960s cast iron laterals were coated with mineral scale and rust. A snake only poked a small hole, and the backup returned within weeks.
After: We jetted at 1,800 PSI to protect the aging pipe. The camera showed the scale was gone and the pipe walls were still intact. Both units drained freely. The job took three hours for both lines.
Book this service → Problems we solve
Drain problems we solve with hydro jetting
Most brea drain calls fall into four categories: grease, roots, scale, and foreign objects. Each one needs a different nozzle and pressure setting. We diagnose with a camera first so we use the right tool, not the biggest hammer.
Ask a pro →Kitchen sink drains slowly and smells
We jet the kitchen branch and main line with hot water at 3,000 PSI to strip the grease layer completely. Most kitchen lines clear in 45 to 60 minutes. We also check the trap arm and vent for partial blockages.
Sewer backs up into the yard or floor drain
We camera the lateral, locate the blockage, and jet with a root-cutting nozzle. If the pipe is cracked, we show you the footage and discuss sewer line repair or trenchless options. Most root jobs take two to three hours.
Multiple fixtures drain slowly at once
We jet the main line from the cleanout to the city main, then verify flow at every fixture. If the camera shows a belly or offset joint, we note it for future repair. This is the most common hydro jetting brea CA call we run.
Recurring clogs after snaking
Hydro jetting removes the entire buildup, not just a channel. We jet the full circumference of the pipe and flush the debris to the main. Customers who switch from snaking to jetting usually go 12 to 24 months between cleanings.
Proof you can check
Licensed, insured, and reviewed
- California C-36 Plumbing License · California State License Board (CSLB)
- Backflow Prevention Certification · California Department of Public Health
- OSHA Safety Certification · Occupational Safety and Health Administration
- Uniform Plumbing Code (UPC) Compliance · International Association of Plumbing and Mechanical Officials (IAPMO)
Customer reviews
What brea customers say
★★★★★
“Our kitchen sink backed up every few months for two years. Ace ran a camera, found grease and root hairs, and jetted the line. That was eight months ago and it still drains fast. They showed us the before-and-after video on their tablet. Fair price, no upsell.”
MG
Maria G.Homeowner, Downtown Brea
✓ Verified“
★★★★★
“We manage a fourplex with cast iron drains from the 1960s. Ace adjusted pressure for the old pipe and cleared two units in one afternoon. They noted one section with minor scaling and told us to watch it, not replace it. Honest work, and they cleaned up after themselves.”
DS
Derek S.Property Manager, Olinda
✓ Verified★★★★★
“A root ball blocked our sewer line on a Sunday. Ace answered the phone, arrived in about an hour, and had the line flowing before dinner. They used a root-cutting nozzle and camera to confirm it was clear. We signed up for annual jetting after that.”
PN
Priya N.Homeowner, Carbon Canyon
✓ VerifiedMost residential hydro jetting jobs in brea run $350 to $650 in 2026, depending on line length, clog type, and access. Root intrusion and heavy grease take longer than a simple scale removal. We quote a flat price after the camera inspection, so you know the number before we start. No hidden fees, no hourly creep.
Yes, when pressure is matched to pipe material. We inspect with a camera first and dial down to 1,500 to 2,000 PSI for older cast iron or Orangeburg lines. PVC and ABS can handle 3,000 to 4,000 PSI. We stop immediately if we see thin walls, cracks, or failing joints.
Most brea homes do well with jetting every 12 to 24 months. If you have large trees near the sewer lateral or a busy kitchen, annual service is better. Restaurants and multi-unit buildings often need quarterly cleaning. We note your line condition after each visit so you can plan ahead.
Yes. We use a root-cutting nozzle that slices roots and flushes them out of the line. Most root jobs take two to three hours. If roots have cracked the pipe, jetting clears the blockage but the pipe may still need repair. We show you the camera footage and explain your options.
Ready when you are
Schedule hydro jetting brea CA today
One call gets a licensed tech to your door with a camera and a jetting machine. We clear the line, show you the footage, and leave the area clean. Call 714 880 7135 now and we will give you a same-day window.
Book Hydro Jetting 714 880 7135 →
Request an appointment
Call Ace Plumbing Brea CA
Reach us at 714 880 7135 for same-day service or 24/7 emergency dispatch. We answer the phone, ask what's going on, and give you a realistic arrival window. Most calls placed before noon get a plumber the same day. You can also email info@aceplumbingbreaca.com for non-urgent quotes and scheduling.
Call anytime714 880 7135Email the officeinfo@plumbingbreaca.com
Office hoursOpen 24 hours · 7 days a week